Software Bisque Error Codes

If you encounter an error while running TheSky6, or any Software Bisque application, check the list of error codes below for an explanation of the error.

 

ERR_NOERROR 0//|No error.|

 

//TheSky6 Telescope errors

 

ERR_COMMNOCONNECTION 200//|No connection.|

ERR_COMMOPENING 201//|Could not open communications port.  The port is either in use by another application or not recognized by the system.|

ERR_COMMSETTINGS 202//|The communications port could not support the specified settings.|

ERR_NORESPONSE 203//|No response from the device.|

ERR_MEMORY 205//|Error: memory error.|

ERR_CMDFAILED 206//|Error: command failed.|

ERR_DATAOUT 207//|Transmit time-out.|

ERR_TXTIMEOUT 208//|Transmit time-out.|

ERR_RXTIMEOUT 209//|Receive time-out.|

ERR_POSTMESSAGE 210//|Post message failed.|

ERR_POINTER 211//|Pointer error.|

ERR_ABORTEDPROCESS 212//|Process aborted.|

ERR_AUTOTERMINATE 213//|Error, poor communication, link automatically terminated.|

ERR_INTERNETSETTINGS 214//|Error, cannot connect to host.|

ERR_NOLINK 215//|No response from the device.|

ERR_PARKLOST 216//|The mount was not able to unpark.|

ERR_DRIVERNOTFOUND 217//|A necessary driver was not found.|

ERR_LIMITSEXCEEDED  218//|Limits exceeded.|

ERR_COMMANDINPROGRESS   219//|Command in progress.|

ERR_DEVICENOTSUPPORTED 220//|Device not supported.|

ERR_NOTPOINT 221//|TPoint model not available.|

ERR_NOTSYNCED 222//|Unable to slew, mount not yet synced.|

ERR_USERASCLIENT 223//|You must use the RASClient application to connect to a remote observatory.|

ERR_THESKYNOTRUNNING    224//|The attempted operation requires the TheSky Level IV and it must be running.|

ERR_NODEVICESELECTED 225//|No device has been selected.|

IDS_CANTLAUNCHTHESKY 226//|Unable to launch TheSky.|

ERR_NOTINITIALIZED 227//|Telescope not initialized. The telescope must be initialized in order to perform this operation.|

ERR_COMMANDNOTSUPPORTED 228//|This command is not supported by the selected device.|

FLASH_REPROGRAMMED 3015//|Turn off power, move dip switches to off posn, then turn power on and reconnect.|

 

// TheSky6 other errors

ERR_OBJECTNOTFOUND 250//|Object not found.|

ERR_OBJECTTOOLOW 251//|Object too low.|

ERR_MISSING_NIGHTVISIONMODE_THEME 252//|Setting Night Vision Mode failed. The required file: 'TheSky6 Night Vision Mode.Theme' cannot be loaded. Options: 1. Copy this file from TheSky6's folder to the My Documents folder. 2. Click Start, Control Panel, Display and load the 'Windows Classic' theme. 3. Reinstall TheSky. 4. Search TheSky6's Help for details about Night Vision Mode and Themes.|

ERR_DISPLAY_PROPS_ALREADY_RUNNING 253//|The Windows Display Properties dialog is open.  Please close it and try again.|

ERR_THEME_NOT_SAVED   254//|Night Vision cannot be invoked because the current theme has been modified without being saved. Please save the current theme by clicking Start, Control Panel, Display, and from the Themes tab, click Save As.|

//Packet Errors

ERR_BADPACKET 300//|Bad packet.|

ERR_BADCHECKSUM 301//|Bad checksum.|

ERR_UNKNOWNRESPONSE 302//|Unknown response.|

ERR_UNKNOWNCMD 303//|Unknown command.|

ERR_BADSEQUENCENUM 304//|Bad sequence number.|

ERR_ENCRYPTION 305//|Packet encryption failed.|

//Track and Accumulate Errors

ERR_TASHIFT 400//|Track and Accumulate Shift Error.|

ERR_TAACCUM 401//|Track and Accumulate Accumulation Error.|

ERR_TACENTROID 402//|Track and Accumulate Centroid Error.|

ERR_TAREMOVEPEDESTAL 403//|Track and Accumulate Pedestal Error.|

ERR_TASUBOFFSET  404//|Track and Accumulate Subtract Offset.|

ERR_TARESIZEIMAGE    405//|Track and Accumulate Resize Error.|

ERR_TACLEARBUF      406//|Track and Accumulate Clear Buffer.|

ERR_TAFINDMINMAX      407//|Track and Accumulate find min/max error.|

ERR_TASTARBRTDOWN50    408//|Track and Accumulate star brightness down 50%.|

ERR_TAUSERRECTNOTFOUND  409//|Track and Accumulate rectangle not found.|

//Combine Errors

ERR_COMBINE_BPP      500//|Combine not available for the image bits-per-pixel.|

ERR_COMBINE_FILETYPE   501//|Incorrect file type for this combine function.|

ERR_COMBINE_READTRKLST  502//|Error reading track list.|

ERR_OUTOFDISKSPACE 503//|Out of disk space.|

ERR_SATURATEDPIXELS 504//|Cannot proceed, saturated pixels found. If possible lower your exposure time.|

ERR_FILEAREREADONLY 505//|Unable to complete operation because file(s) are read only.|

ERR_PATHNOTFOUND 506//|Unable to create or access the folder.|

ERR_FILEMUSTBESAVED 507//|Please save the image before using this command.|

 

//Autoguide/Calibration Errors

ERR_STARTOODIM1 550//|Star too dim.  Lost during +X move.|

ERR_STARTOODIM2 551//|Star too dim.  Lost during -X move.|

ERR_STARTOODIM3 552//|Star too dim.  Lost during +Y move.|

ERR_STARTOODIM4 553//|Star too dim.  Lost during +Y move.|

ERR_MOVEMENTTOOSMALL1 554//|Motion too small during +X move.  Increase calibration time.|

ERR_MOVEMENTTOOSMALL2 555//|Motion too small during -X move.  Increase calibration time.|

ERR_MOVEMENTTOOSMALL3 556//|Motion too small during +Y move.  Increase calibration time.|

ERR_MOVEMENTTOOSMALL4 557//|Motion too small during -Y move.  Increase calibration time.|

ERR_STARTOOCLOSETOEDGE1  558//|Star too close to edge after +X move.|

ERR_STARTOOCLOSETOEDGE2  559//|Star too close to edge after -X move.|

ERR_STARTOOCLOSETOEDGE3  560//|Star too close to edge after +Y move.|

ERR_STARTOOCLOSETOEDGE4  561//|Star too close to edge after -Y move.|

ERR_AXISNOTPERPENDICULAR1 562//|Invalid motion in X axis.|

ERR_AXISNOTPERPENDICULAR2 563//|Invalid motion in Y axis.|

ERR_BOTHAXISDISABLED      564//|Unable to calibrate, both axis are disabed.  At least one axis must be enabled to calibrate.|

ERR_RECALIBRATE        565//|Re-calibrate required.  Declination at calibration is unknown.|

ERR_NOBRIGHTOBJECTFOUND   566//|No bright object found on image.|

//DSSDLL Errors

ERR_DSSNAMETOLONG 600//|The file name and/or path is too long.|

ERR_DSSNOTINITED        601//|The DSS is not properly initialized, please check DSS Setup parameters.|

ERR_DSSSYSERROR 602//|System error.  Please verify DSS Setup parameters and make sure you have the correct disk in the CD-ROM drive.|

ERR_DSSWRONGDISK 603//|Wrong Disk.|

ERR_DSSNOIMAGE 604//|No image found to extract.|

//SB DSS UI Errors

ERR_DSSINVALIDCOORDINATE 605//|Invalid coordinate(s).|

ERR_DSSINVALIDSIZE  606//|Invalid size.|

ERR_DSSDLLOLD  607//|The file DSS_DLL.DLL is old and not compatible with this program. Please obtain the latest DSS_DLL.DLL.|

ERR_DSSCDROM  608//|Unable to access the CD-ROM drive specified in DSS Setup.  Make sure the drive is valid and/or there is a CD-ROM in the drive.|

ERR_DSSHEADERSPATH  609//|Unable to access the headers path specified in DSS Setup.  Please correct the path.|

ERR_DSSNODSSDISK  610//|A DSS CD-ROM disk is not present in the CD-ROM drive.  Please insert one before continuing.|

ERR_DSSNOTINSURVEY  611//|Not in survey.|

// Image Link/AutoMap

ERR_ILINK_NOSCALE 650//|Image link has no image scale.|

ERR_ILINK_TOOFEWBMP 651//|Image link failed because there are not enough stars in the image.  Try adjusting the image's background and range.|

ERR_ILINK_TOOFEWSKY 652//|Image Link failed because there are an insufficient number of matching cataloged stars.  There must be at least six cataloged stars in each image to perform an Image Link. Use the USNO stellar database for more stars.|

ERR_ILINK_NOMATCHFOUND 653//|Image Link failed, no pattern matching found.  Check image coordinates and image scale.|

ERR_ILINK_NOIMAGE 654//|Image Link failed because there is no image to match.|

 

//General Errors

ERR_SKIPIMAGE 700//|Skip image error.|

ERR_BADFORMAT 701//|Unrecognized or bad file format.|

ERR_COMMANDUNSUCCESSFUL 206//|Error: command failed.|

ERR_LPARAMNULL 211//|Pointer error.|

ERR_OPENINGFILE 702//|Unable to open file.|

ERR_FEATURENAINLEVEL 703//|This Level does not support this feature.|

ERR_SOCKETEXCEPTION 704//|An error occurred during a network call.|

ERR_CANTCREATETHREAD 705//|Unable to create a new thread.|

ERR_F_DOESNOTEXIST 709//|The file or folder does not exist.|

ERR_F_ACCESS_WRITE 707//|Access denied. You do not have write access to the file or folder.|

ERR_F_ACCESS_READ 706//|Access denied. You do not have read access to the file or folder.|

ERR_F_ACCESS_RW 708//|Access denied. You do not have read/write access to the file or folder.|

ERR_CHANGE_PASSWORD 710//|You are required to change your password before you can access this site.|

 

//For creating and decoding wire safe SCODES

SBSCODEBASE 1000

 

//Self Guide Errors

ERR_SGSTARBRTDOWN50    800//|Self-guide star brightness down 50%.|

ERR_SGNEXT 801//|Self-guide next error.|

ERR_SGNEXT2 802//|Self-guide next two error.|

ERR_MNCPFIRSTERROR 900//|MNCP first error.|

ERR_MNCPLASTERROR 999//|MNCP last error.|

//SBIG Camera Errors

ERR_SBIGST7FIRST 1000

ERR_SBIGCCCFWFIRST 1040

 

CE_CAMERA_NOT_FOUND 1001//|SBIG driver: Camera not found.|

CE_EXPOSURE_IN_PROGRESS 1002//|SBIG driver: Exposure already in progress.|

CE_NO_EXPOSURE_IN_PROGRESS 1003//|SBIG driver: Exposure not in progress.|

CE_UNKNOWN_COMMAND 1004//|SBIG driver: Bad PC Command.|

CE_BAD_CAMERA_COMMAND 1005//|SBIG driver: Bad camera command.|

CE_BAD_PARAMETER 1006//|SBIG driver: Bad parameter.|

CE_TX_TIMEOUT 1007//|SBIG driver: Transmission timeout.|

CE_RX_TIMEOUT 1008//|SBIG driver: Receive timeout.|

CE_NAK_RECEIVED 1009//|SBIG driver: NAK received.|

CE_CAN_RECEIVED 1010//|SBIG driver: CAN received.|

CE_UNKNOWN_RESPONSE 1011//|SBIG driver: Unknown response.|

CE_BAD_LENGTH 1012//|SBIG driver: Bad length.|

CE_AD_TIMEOUT 1013//|SBIG driver: A/D timeout.|

CE_KBD_ESC 1014//|SBIG driver: Keyboard Escape.|

CE_CHECKSUM_ERROR 1015//|SBIG driver: Checksum error.|

CE_EEPROM_ERROR 1016//|SBIG driver: EEPROM error.|

CE_SHUTTER_ERROR 1017//|SBIG driver: Shutter error.|

CE_UNKNOWN_CAMERA 1018//|SBIG driver: Unknown camera.|

CE_DRIVER_NOT_FOUND 1019//|SBIG driver: Driver not found.|

CE_DRIVER_NOT_OPEN 1020//|SBIG driver: Driver not open.|

CE_DRIVER_NOT_CLOSED 1021//|SBIG driver: Driver not closed.|

CE_SHARE_ERROR 1022//|SBIG driver: Driver share error.|

CE_TCE_NOT_FOUND 1023//|SBIG driver: TCE not found.|

CE_AO_ERROR 1024//|SBIG driver: AO error.|

CE_ECP_ERROR 1025//|SBIG driver: ECP error.|

CE_MEMORY_ERROR 1026//|SBIG driver: Memory error.|

CE_DEVICE_NOT_FOUND 1027//|SBIG driver: Device not found.|

CE_DEVICE_NOT_OPEN 1028//|SBIG driver: Device not open.|

CE_DEVICE_NOT_CLOSED 1029//|SBIG driver: Device not closed.|

CE_DEVICE_NOT_IMPLEMENTED 1030//|SBIG driver: Device not implemented.|

CE_DEVICE_DISABLED 1031//|SBIG driver: Device disabled.|

CE_OS_ERROR 1032//|SBIG driver: Operating system error.|

CE_SOCK_ERROR 1033//|SBIG driver: Socket error.|

CE_SERVER_NOT_FOUND 1034//|SBIG driver: Server not found.|

CE_CFW_ERROR 1035//|SBIG driver: General CFW error.|

//SBIG CFW Errors

CE_CFWE_NONE 1040//|SBIG driver: CFW error none.|

CE_CFWE_BUSY 1041//|SBIG driver: CFW error busy.|

CE_CFWE_BAD_COMMAND 1042//|SBIG driver: CFW error bad command.|

CE_CFWE_CAL_ERROR 1043//|SBIG driver: CFW error calibration error.|

CE_CFWE_MOTOR_TIMEOUT 1043//|SBIG driver: CFW error motor timeout.|

CE_CFWE_BAD_MODEL 1045//|SBIG driver: CFW error bad model.|

ERR_SBIGST7LAST 1049

ERR_SBIGTCEEXTFIRST 1050

 

TCEEE_LIMIT_HIT 1051//|Limit hit.|

TCEEE_USER_ABORT 1052//|User abort.|

TCEEE_RA_TIMEOUT 1053//|RA time-out.|

TCEEE_DEC_TIMEOUT 1054//|Dec time-out.|

TCEEE_COM_MOTION_TIMEOUT 1055//|Communications motion time-out.|

TCEEE_RA_COM_ERROR 1056//|RA communication error.|

TCEE_DEC_COM_ERROR 1057//|Dec communication error.|

#endif

ERR_SBIGTCEEXTLAST 1099

 

//SBIG Serial Errors

ERR_SBIGSERIALFIRST 1100

ERR_SBIGSERIALLAST 1125

ERR_AUTOSAVE 1130//|Auto-save error.|

 

//SBIG CCDOPS ERRORS

ERR_UPLOADNOTST6FILE 1150

ERR_NOHEADADJNEEDED 1151

ERR_NOTCFW6A 1152

ERR_NOINTERFACE 1153

ERR_CAMERANOTFOUND 1154

ERR_BAUDSWITCHFAILED 1155

ERR_CANNOTUPLOADDARK 1156

ERR_SKIPPINGDARK 1157

ERR_SKIPPINGLIGHT 1158

ERR_SELFGUIDENA 1159

ERR_TRACKLOGNA 1160

ERR_AOREQUIREST78 1161

ERR_CALIBRATEAONOTON 1162

ERR_WRONGCAMERAFOUND 1163//|A camera was detected, but it does not match the one selected.|

ERR_PIXEL_MATH_OPERAND 1164//|Can not multiply or divide the image pixels by an operand less than 0.001.|

ERR_IMAGE_SIZE 1165//|Enlarged image would exceed maximum image size. Try cropping it first.|

ERR_CANNOT_COLORGRAB 1166//|There is not a color filter wheel attached.|

ERR_WRONGCFWFOUND 1167//|A filter was detected, but it does not match the one selected.|

 

//APOGEE Camera Errors

ERR_APOGEEFIRST 1200

ERR_APOGEECFGNAME 1200//|A required initialization file was not found.  Go to Camera, Setup, and press the Settings button to choose the correct file.|

ERR_APOGEECFGDATA 1201//|Error in Apogee INI file.|

ERR_APOGEELOAD 1202//|Error transferring APCCD.INI data to camera.|

ERR_APOGEEOPENOFFSET 1220//|Invalid base I/O address passed to func.|

ERR_APOGEEOPENOFFSET1 1221//|Register access operation error.|

ERR_APOGEEOPENOFFSET2 1222//|Invalid CCD geometry.|

ERR_APOGEEOPENOFFSET3 1223//|Invalid horizontal binning factor.|

ERR_APOGEEOPENOFFSET4 1224//|Invalid vertical binning factor.|

ERR_APOGEEOPENOFFSET5 1225//|Invalid AIC value.|

ERR_APOGEEOPENOFFSET6 1226//|Invalid BIC value.|

ERR_APOGEEOPENOFFSET7 1227//|Invalid line offset value.|

ERR_APOGEEOPENOFFSET8 1228//|CCD controller sub-system not initialized.|

ERR_APOGEEOPENOFFSET9 1229//|CCD cooler failure.|

ERR_APOGEEOPENOFFSET10 1230//|Failure reading image data.|

ERR_APOGEEOPENOFFSET11 1231//|Invalid buffer pointer specfied.|

ERR_APOGEEOPENOFFSET12 1232//|File not found or not valid.|

ERR_APOGEEOPENOFFSET13 1233//|Config. data invalid.|

ERR_APOGEEOPENOFFSET14 1234//|Invalid CCD handle passed to function.|

ERR_APOGEEOPENOFFSET15 1235//|Invalid parameter passed to function.|

ERR_APOGEELAST 1299

 

//define Shutter Timing

ERR_GPSTFPNOTRUNNING 1300//|Shutter timing is enabled, but the GPSTFP application is not running.|

 

//Custom error codes for third

//parties supporting SB's APIs

//should reside between

ERR_CUSTOMAPIFIRST 1400

ERR_CUSTOMAPILAST 1499

ERR_IPLSUITEERR 1500

ERR_APOGEEOPENOFFSET15 1235//|Invalid parameter passed to function.|

ERR_GDIERR_BASE 1600

 

// Image calibration

ERR_IMAGECALWRONGBPP 5000 //|Unable to reduce. The image being reduced doesn't have the same bits per pixel as the reduction frames.|

ERR_IMAGECALWRONGSIZE 5001 //|Unable to reduce. The image being reduced is larger than the reduction frames.|

ERR_IMAGECALWRONGBIN 5002 //|Unable to reduce. The image being reduced doesn't have the same bin mode as the reduction frames.|

ERR_IMAGECALWRONGSUBFRAME 5003 //|Unable to reduce. The image being reduced doesn't entirely overlap the reduction frames. Make sure the subframes overlap.|

ERR_IMAGECALGROUPINUSE 5004 //|Unable to proceed. The reduction group is currently in use.|

ERR_IMAGECALNOSUCHGROUP 5005 //|Unable to proceed. The selected reduction group no longer exists.|

ERR_IMAGECALNOFRAMES 5006 //|Unable to proceed. The selected reduction group does not contain any reduction frames.|

 

// Combine

ERR_WRONGBPP 5020 //|Unable to proceed. The images don't have the same bits per pixel.|

ERR_WRONGSIZE 5021 //|Unable to proceed. The images don't have the same dimensions.|

ERR_WRONGTYPE 5022 //|Unable to proceed. The images don't have the same format.|

 

// Align folder

ERR_NOIMAGESINFOLDER 5050 //|Unable to proceed. The folder doesn't contain any readable images.|

ERR_NOPATTERNMATCH 5051 //|The files could not be aligned. No pattern match was found.|

 

// FITS related errors

ERR_NOTFITS 5070 //|This operation requires a FITS file.|

 

// Curve Funcs Return Values

ERR_KVW_NOMINIMA 6000 //|KVW_NOMINIMA.|

ERR_KVW_DETERMINANTZERO 6001 //|KVW_DETERMINANTZERO.|

ERR_KVW_DIVISIONBYZERO 6002 //|KVW_DIVISIONBYZERO.|

ERR_KVW_NOTENOUGHPOINTS 6003 //|KVW_NOTENOUGHPOINTS.|

ERR_AF_ERRORFIRST 7000 //|@Focus error.|

ERR_AF_DIVERGED 7001 //|@Focus diverged. |

ERR_AF_UNDERSAMPLED 7003 //|Insufficient data to measure focus, increase exposure time. |

ERR_FLICCD_E_FIRST 8000 //|ERR_FLICCD_E_FIRST|

ERR_FLICCD_E_NOTSUPP 8001 //|ERR_FLICCD_E_NOTSUPP|

ERR_FLICCD_E_INVALID_PARAMETER 8002 //|ERR_FLICCD_E_INVALID_PARAMETER|

ERR_FLICCD_E_INVALID_COMPORT 8003 //|ERR_FLICCD_E_INVALID_COMPORT|

ERR_FLICCD_E_COMPORT_ERROR 8004 //|ERR_FLICCD_E_COMPORT_ERROR|

ERR_FLICCD_E_FAILED_RESET 8005 //|ERR_FLICCD_E_FAILED_RESET|

ERR_FLICCD_E_COMMTIMEOUT 8006 //|ERR_FLICCD_E_COMMTIMEOUT|

ERR_FLICCD_E_BADDATA 8007 //|ERR_FLICCD_E_BADDATA|

ERR_FLICCD_E_NOCALIBRATE 8008 //|ERR_FLICCD_E_NOCALIBRATE|

ERR_FLICCD_E_DEVICE_NOT_CONFIGURED 8009 //|ERR_FLICCD_E_DEVICE_NOT_CONFIGUR|

ERR_FLICCD_E_COMMWRITE 8010 //|ERR_FLICCD_E_COMMWRITE|

ERR_FLICCD_E_INVALID_DEVICE 8011 //|ERR_FLICCD_E_INVALID_DEVICE|

ERR_FLICCD_E_FUNCTION_NOT_SUPPORTED 8012 //|ERR_FLICCD_E_FUNCTION_NOT_SUPPORTED|

ERR_FLICCD_E_BAD_BOUNDS 8013 //|ERR_FLICCD_E_BAD_BOUNDS|

ERR_FLICCD_E_GRABTIMEOUT 8014 //|ERR_FLICCD_E_GRABTIMEOUT|

ERR_FLICCD_E_TODATAHB 8015 //|ERR_FLICCD_E_TODATAHB|

ERR_FLICCD_E_TODATALB 8016 //|ERR_FLICCD_E_TODATALB|

ERR_FLICCD_E_ECPNOTREADY 8017 //|ERR_FLICCD_E_ECPNOTREADY|

ERR_FLICCD_E_ECPREADTIMEOUTHB 8018 //|ERR_FLICCD_E_ECPREADTIMEOUTHB|

ERR_FLICCD_E_ECPREADTIMEOUTLB 8019 //|ERR_FLICCD_E_ECPREADTIMEOUTLB|

ERR_FLICCD_E_ECPREADTIMEOUT 8020 //|ERR_FLICCD_E_ECPREADTIMEOUT|

ERR_FLICCD_E_ECPREVERSETIMEOUT 8021 //|ERR_FLICCD_E_ECPREVERSETIMEOUT|

ERR_FLICCD_E_ECPWRITETIMEOUTHB 8022 //|ERR_FLICCD_E_ECPWRITETIMEOUTHB|

ERR_FLICCD_E_ECPWRITETIMEOUTLB 8023 //|ERR_FLICCD_E_ECPWRITETIMEOUTLB|

ERR_FLICCD_E_ECPWRITETIMEOUT 8024 //|ERR_FLICCD_E_ECPWRITETIMEOUT|

ERR_FLICCD_E_FORWARDTIMEOUT 8025 //|ERR_FLICCD_E_FORWARDTIMEOUT|

ERR_FLICCD_E_NOTECP 8026 //|ERR_FLICCD_E_NOTECP|

ERR_FLICCD_E_FUNCTIONNOTSUPP 8027 //|ERR_FLICCD_E_FUNCTIONNOTSUPP|

ERR_FLICCD_E_NODEVICES 8028 //|ERR_FLICCD_E_NODEVICES|

ERR_FLICCD_E_WRONGOS 8029 //|ERR_FLICCD_E_WRONGOS|

ERR_TEMMA_RAERROR 8030 //|Slew error: right ascension incorrect|

ERR_TEMMA_DECERROR 8031 //|Slew error: declination incorrect|

ERR_TEMMA_TOOMANYDIGITS             8032 //|Slew error: object below the horizon|

 

//ACL Errors-Values defined by ACL

ERR_ACLUNDEFINEDERR 1//|ACL undefined error.|

ERR_ACLSYNTAX 2//|ACL syntax error.|

ERR_ACLTYPEMISMATCH 10//|ACL type mismatch error.|

ERR_ACLRANGE 11//|ACL range error.|

ERR_ACLVALREADONLY 12//|ACL value is read only.|

ERR_ACLCMDUNSUPPORTED 13//|ACL command is unsupported.|

ERR_ACLUNSUPPORTID 14//|ACL unsupported id.|

ERR_ACLCMDINACTIVE 15//|ACL command inactive.|

//ACL Base Telescope Errors

ERR_ACLGOTOILLEGAL 100//|ACL illegal goto command.|

ERR_ACLGOTOBELOWHRZ 101//|ACL error: destination is below the horizon.|

ERR_ACLGOTOLIMITS 102//|ACL goto limit.|

 

MKS_ERROR_FIRST 20000

MKS_ERROR_LAST  25000

 

COMM_BASE 21000//|COMM_BASE.|

COMM_OKPACKET 21000//|COMM_OKPACKET.|

COMM_NOPACKET 21001//|Serial command packet not included with command. COMM_NOPACKET.|

COMM_TIMEOUT 21002//|Receive time-out.COMM_TIMEOUT.|

COMM_COMMERROR 21003//|Serial communication error. COMM_COMMERROR.|

COMM_BADCHAR 21004//|Invalid serial command error. COMM_BADCHAR.|

COMM_OVERRUN 21005//|Packet overrun error. COMM_OVERRUN.|

COMM_BADCHECKSUM 21006//|Bad checksum error. COMM_BADCHECKSU.|

COMM_BADLEN 21007//|Invalid length of serial command error. COMM_BADLEN.|

COMM_BADCOMMAND 21008//|Invalid serial command error. COMM_BADCOMMAND.|

COMM_INITFAIL 21009//|Could not open communications port.  The port is either in use by another application or not recognized by the system. COMM_INITFAIL|

COMM_NACK 21010//|No acknowledgement of command from device. COMM_NACK.|

COMM_BADID 21011//|Invalid identifier. COMM_BADID.|

COMM_BADSEQ 21012//|Invalid command sequence. COMM_BADSEQ.|

COMM_BADVALCODE 21013//|Invalid command code. COMM_BADVALCODE.|

MAIN_BASE 22000//|MAIN_BASE.|

MAIN_WRONG_UNIT 22001//|MAIN_WRONG_UNIT.|

MAIN_BADMOTORINIT 22002//|MAIN_BADMOTORINIT.|

MAIN_BADMOTORSTATE 22003//|Unable to slew because the mount has not been homed. Click Telescope, Options, Find Home to home the mount.|

MAIN_BADSERVOSTATE 22004//|Indexing before finding switch 1.|

MAIN_SERVOBUSY 22005//|Indexing before finding switch 1.|

MAIN_BAD_PEC_LENGTH 22006//|Invalid length of PEC table. MAIN_BAD_PEC_LENGTH.|

MAIN_AT_LIMIT 22007//|The mount is at a minimum or maximum position limit and cannot be slewed.  This error may be the result of improper synchronization near the meridian. When syncing near the meridian, be sure the optical tube assembly and the synchronization star are on opposite sides of the meridian.|

MAIN_NOT_HOMED 22008//|Mount has not been homed. Click Telescope, Options, Find Home to home the mount.|

MAIN_BAD_POINT_ADD 22009//|Object-Tracking point error.|

MAIN_BAD_CONTROL_CODE 22020//|MKS4000: Command-code is invalid.|

MAIN_BAD_SYSTEM_ID 22021//|Unknown system type (not an MKS 3000 or MKS 4000)|

FLASH_BASE 23000//|FLASH_BASE.|

FLASH_PROGERR 23001//|FLASH_PROGERR.|

FLASH_ERASEERR 23002//|FLASH_ERASEERR.|

FLASH_TIMEOUT 23003//|FLASH_TIMEOUT.|

FLASH_CANT_OPEN_FILE 23004//|FLASH_CANT_OPEN_FILE.|

FLASH_BAD_FILE 23005//|FLASH_BAD_FILE.|

FLASH_FILE_READ_ERR 23006//|FLASH_FILE_READ_ERR.|

FLASH_BADVALID 23007//|FLASH_BADVALID.|

FLASH_INVALID_SECTION 23008//|MKS4000: Invalid FLASH section.|

FLASH_INVALID_ADDRESS 23009//|MKS4000: Invalid FLASH address.|

MOTOR_BASE 24000//|MOTOR_BASE.|

MOTOR_OK 24000//|MOTOR_OK.|

MOTOR_OVERCURRENT 24001//|MOTOR_OVERCURRENT.|

MOTOR_POSERRORLIM 24002//|Maximum position error exceeded.|

MOTOR_STILL_ON 24003//|Motor still slewing but command needs it stopped.|

MOTOR_NOT_ON 24004//|Motor off.|

MOTOR_STILL_MOVING 24005//|Motor still slewing but command needs it stopped.|

MOTOR_FIELD_TIMEOUT 24006//|Timed out while fielding.|

MOTOR_BAD_CONTROL_STATE 24007//|MOTOR_BAD_CONTROL_STATE.|

MOTOR_BAD_SERVO_STATE 24005//|MOTOR_BAD_SERVO_STATE.|

 

E_SI_BASE 9000//Put into sberror when have source contrl

E_TIMEOUT 9001//|SI Driver: Timeout.|

E_DATA_ERROR 9002//|SI Driver: Data error.|

E_COM_ERROR 9003//|SI Driver: COM error.|

E_DMA_ACTIVE 9004//|SI Driver: DMA active.|

E_DMA_NOT_ACTIVE 9005//|SI Driver: DMA not active.|

E_BAD_SET_FILE 9010//|The settings file (.SET) does not exist or cannot be read.|

E_BAD_BIN_FILE 9011//|The binary code file (.BIN) does not exist or cannot be read.  Check the "DSP Code File Name" referenced in your settings file.|

E_SUBFRAME_ONE_PORT 9012//|Subframes are only supported when using one port.  Remove the checkmark next to Subframe on the Take Image tab, or go to the Camera Setup tab, Settings and set Port to "One."|